NOTICE توجه: این یک موضوع قدیمی است که آخرین پست ارسالی آن مربوط به 2146 روز قبل است . لطفا فقط پاسخ ها ، سوالات و درخواست های 100 درصد مرتبط را به آن ارسال کنید و برای درخواست ها و سوالات جدید موضوع جدیدی را ایجاد کنید
صفحه 1 از 3 123 آخرینآخرین
نمایش نتایج: از 1 به 20 از 52

موضوع: آمپلیفایرها

  1. #1
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    Gadid آمپلیفایرها

    سلام.در این قسمت مدارهای پری آمپلیفایر و آمپلیفایرهای مختلف قرار میدهیم.
    ویرایش توسط javad naderi : 14-04-2011 در ساعت 13:09

  2. تشکرها از این نوشته :


  3. # ADS
    Circuit advertisement
    تاریخ عضویت
    Always
    نام
    Advertising world
    نوشته ها
    Many
     

  4. #2
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    10W Mini Audio Amplifier










    Componets ListR1 : 6 Ohm
    R2 : 220 Ohm
    R3 : nothing
    R4 : 10 KOhm pontesiometer
    C1 : 2200 uF / 25V
    C2 : 470 uF / 16V
    C3 : 470 nF / 63V
    C4 : 100 nF
    C5 : nothing
    C6 : nothing
    IC1 : TDA 2003

  5. تشکرها از این نوشته :


  6. #3
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    2N3055 Power Amplifier

    Simple and low cost. The optimal supply voltage is around 50V, but this amp work from 30 to 60V. The maximal input voltage is around 0.8 - 1V. As you can see, in this design the components have a big tolerance, so you can build it almost of the components, which you find at home. The and transistors can be any NPN type power transistor, but do not use Darlington types... The output power is around 60W.





    Some comments:
    - capacitor C1 regulates the low frequencies (bass), as the capacitance grows, the low frequncies are getting louder.
    - capacitor C2 regulates the higher frequencies (treble), as the capacitance grows, the higher frequencies are getting quiter.
    - this is a class B amplifier, this means, that a current must flow through the end transistors, even if there is no signal on the input. This current can be regulated with the 500Ω trimmer resistor. As this current incrases, the sound of the amplifier gets better, but the end transistors are more heating. But if this current decrases, the transistors are not heating so much, but the sound gets worse...



    Amplifier schematic:




    http://www.electronics-lab.com/proje..._Amplifier.zip

  7. تشکرها از این نوشته :


  8. #4
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    20W Audio Amplifier using LM1875





    20W Audio Amplifier kit is based on LM1875 IC.


    Power supply - 48 VDC

    Output - 20 W, 4 Ω

    Very low distortion (THD - 0.015%), good channel separation and ripple rejection

    IC built-in thermal, short circuit protections

    Internal output protection diodes

    Terminal pins for connecting input

    Power Battery Terminal (PBT) for easy power supply and speaker connection

    Power-On LED indicator

    Heatsink for IC

    Four mounting holes of 3.2 mm each with nut and stud

    PCB dimensions 48 mm x 60 mm











    http://www.electronics-lab.com/proje..._amplifier.pdf

  9. تشکرها از این نوشته :


  10. #5
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    Stereo tape head preamplifier using LA3161











    http://www.electronics-lab.com/proje...EAMPLIFIER.pdf

  11. تشکرها از این نوشته :


  12. #6
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    Universal Preamplifier





    Description




    Most audio amplifier systems must have preamplifiers with many different characteristics. These include high-gain linear response for magnetic microphones, low-gain linear response for tuners, and high-gain RIAA equalization for magnetic phone cartridges.

    To meet this broad requirement, most amplifier designers include a single universal preamplifier circuit. Basically a high-gain linear amplifier, its characteristics can be altered by switching alternative resistor filter networks into its feedback system.

    For example, when the selector switch is set to the Mag phono position, alternative input sources can be selected by S1-a, and appropriate linear-response gain control feedback resistors 220K, 470K, and 1M are now selected by S1-b. Those feedback resistor values are selected between 10 kilo ohms and 10 megohms to suit individual listener tastes. Circuit gain will be proportional, to the feedback resistor value.


    http://www.electronics-lab.com/proje...EAMPLIFIER.PDF

  13. تشکرها از این نوشته :


  14. #7
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    Motorola Hi-Fi power amplifier

    This is a very simple, low cost, Hi-Fi quality power amplifier. You can build it 5 ways, like it’s shown in the table (from 20 W to 80 W RMS).





    Some comments:
    - The first thing that you must do, is to measure the end transistors (T3 and T4) amplifying coefficient, the hfe or β. If their disagreement is bigger than 30 %, the amplifier would not give a clear sound. I used MJ3001 and MJ2501 transistors, and this disagreement was around 5%.
    - Before the first “turning on” you must short circuit the inputs of the amp, and put a mA-meter on the output, than turn the amplifier on, and tune the R13 pot, to decrease the DC current on the output, to some uA-s, or in a lucky situation to zero. I was able to decrease it to 10 uA.





    http://www.electronics-lab.com/proje...torola_amp.zip

  15. تشکرها از این نوشته :


  16. #8
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    20W Bridge Audio Amplifier



    Specifications



    20W Bridge Audio Amplifier kit, based on the TDA2005 IC, a class B dual audio amplifier, specifically designed for car radio applications etc.


    Power supply - 18 VDC

    Output power - 20 W, 4 Ω

    IC built in Thermal Shut-down, Load dump voltage surge protected

    Terminal pins for connecting left and right audio signal inputs

    Relimate Connector for connecting Potentiometer (POT) for volume adjustment

    Power Battery Terminal (PBT) for easy power supply and speaker connection

    Power-On LED indicator

    Heatsink for IC

    Four mounting holes of 3.2 mm each with nut and stud

    PCB dimensions 63 mm x 65 mm



    Schematic





    http://www.electronics-lab.com/proje..._amplifier.pdf

  17. تشکرها از این نوشته :


  18. #9
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    Portable Audio Amplifiers





    Description




    Stereo per channel
    VCC=9V;RL=4?/3W
    VCC=9V;RL=8?/2W

    Bridge Application
    VCC=9V;RL=8?/5W
    VCC=9V;RL=4?/8W

    Supply Voltage min = DC3v @ 500mA
    Supply Voltage max = DC12v @ 500mA
    Supply Voltage recommended = DC9v @500mA

    DESCRIPTION
    Above circuits are based on TEA2025 is a monolithic integrated audio amplifier in a 16-pin plastic dual in line package manufactured by UTC .Circuit has an Internal Thermal Protector. It is designed for portable cassette players and radios. You can also use it as your PC Audio Amplifier. A few external components required to build this circuit. Use 9v transformer to play the circuit. But not more than DC12v. Because it can damage the amplifier IC. So build n Enjoy.


    http://www.electronics-lab.com/proje...AMPLIFIERS.PDF

  19. تشکرها از این نوشته :


  20. #10
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    Tiny audio amplifier using LM386




    Specifications


    The Tiny Audio Amplifier kit is a good choice for battery operation. It is based on LM386 IC.


    Power supply - 6 - 12 VDC

    Output power - 1 W, 8 Ohm

    The quiescent power drain is only 24 mW when operating from 6 VDC

    Self-centering output quiescent voltage

    Onboard PRESET to adjust volume

    Terminal pins for connecting power supply, audio signal and speaker

    Power-On LED indicator

    ON/OFF PCB mounted slide switch for power supply

    Four mounting holes of 3.2 mm each

    PCB dimensions 44 mm x 44 mm



    Schematic





    Inputs - Outputs configuration



    http://www.electronics-lab.com/proje...20AMPLFIER.pdf

  21. کاربران : 3 تشکر کرده اند از شما javad naderi برای ارسال این پست سودمند:


  22. #11
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    600W Audio Amplifier





    POWER :
    Maximum Output power @ 8ohms : 300watt
    Absolute max power supply voltage :±38V to ±40V
    Recommended power supply voltage :±30V to ±35V


    GENERAL DISCRIPTION :
    The circuit is based around {LM4702}manufactured by NATIONAL semiconductors&{MJ11029-MJ11028} by ON semiconductors It is a high fidelity audio power amplifier. Designed for demanding consumer and pro-audio applications. You can also use this circuit with AV receivers, Audiophile power amps, Pro Audio High voltage industrial applications etc Amplifier output power maybe scaled by changing the supply voltage and number of output devices. The circuit includes thermal shutdown circuitry that activates when the die temperature exceeds 150°c. CIRCUIT’s mute function, when activated, mutes the input drive signal and forces the amplifier output to a quiescent state.


    http://www.electronics-lab.com/proje...UDIO%20AMP.pdf

  23. تشکرها از این نوشته :


  24. #12
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    200W Audio Amplifier





    Output Power : 200Watts
    Load Resistance : 8ohms
    Input impedance : 55K
    Maximum supply voltage : (+95v)-0-(-95v)
    Recommended supply voltage : (+66v)-0-(-66v)

    This complete high quality, low noise mono audio power amplifier is based around the Hybrid Integrated Circuit STK4050 manufactured by Sanyo. The circuit incorporates volume and has a maximum music output power of 200W.The circuit incorporates an on board power supply; therefore, only centre tapped transformer is required to power the circuit. I t has very good quality sound. U can use it with your Home Theatre your PC & etc... You can also use it as Subwoofer Amplifier. It is a compact package for THIN-TYPE Audio sets. Easy Heatsink design to disperse heat generated in THIN-TYPE audio sets. Constant-Current circuit to Reduce supply switch-ON and switch-OFF shock noise. External supply switch-On and switch-OFF shock noise muting, Load short-circuit protection, thermal shutdown and other circuits can be tailored-designed.


    http://www.electronics-lab.com/proje...0AMPLIFIER.pdf

  25. تشکرها از این نوشته :


  26. #13
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    آمپلیفایر 300w
    تصاوير کوچک فايل پيوست تصاوير کوچک فايل پيوست برای دیدن سایز بزرگ روی عکس کلیک کنید

نام: 1.JPG
مشاهده: 26
حجم: 54.7 کیلو بایت  
    فايل هاي پيوست شده فايل هاي پيوست شده
    • نوع فایل: rar Desktop.rar (514.7 کیلو بایت, 200 نمايش)

  27. تشکرها از این نوشته :


  28. #14
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    Power Amplifier 300W HIFI by MJ15004,MJ15003



    http://up.iranblog.com/images/ylskll3v1hmg7c1u2fk.doc

  29. #15
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    مدار آمپلی با ماسفت قدرت ۱۰۰ وات












    Output power (f=1 KHz, d=0.5 %): 100 W in 8 ohm
    Supply voltage: ................ ñ 40 V
    Quiescent current: ............. 50 mA
    Maximum current: ............... 2.6 A
    Sensitivity: . 600 mV
    Frequency response: ............ 10-35000 Hz (-1 dB)
    Distortion HD: ................. 0.01 %
    Intermodulation dist.: ......... 0.02 %
    Signal/noise: 83 dBConstruction



  30. تشکرها از این نوشته :


  31. #16
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    مدار امپلی100وات ۸ اهم های فیدلتی ماسفت

    تو این مدار هم میتونین از ماسفت هم ازترانزیستور قدرت استفاده کنین(خود دانید!) راستی بیشتر از۴۵ولت هم دیگه بهش اعمال نکنینا!که وای به حالتون میشه.اگه مشکلی یا سوالی هم داشتین تونظرات مطرح کنین تا دراسرع وقت ژیگیری کنم.البته خودم هم چک میکنم






  32. تشکرها از این نوشته :


  33. #17
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

  34. کاربران : 2 تشکر کرده اند از شما javad naderi برای ارسال این پست سودمند:


  35. #18
    مدیر انجمن javad naderi آواتار ها
    تاریخ عضویت
    Jan 2011
    نام
    جواد نادری زاده
    نوشته ها
    830
    تشکر
    225
    تشکر شده 1,334 بار در 602 پست

    پیش فرض

    دوستان من 2 ماهی نیستم و میرم آموزشی سربازی.امیدورم مطالب من به دردتون خورده باشه.یا غلی

  36. تشکرها از این نوشته :


  37. #19
    عضو جدید
    تاریخ عضویت
    Jun 2011
    نوشته ها
    5
    تشکر
    2
    تشکر شده 2 بار در 2 پست

    پیش فرض

    ممنون از مدار های خوبتون ...
    یه سوال داشتم خدمتتون ،‌ میخواستم بپرسم کدوم یکی از اینا برای افزایش برد hmtr مناسبه ؟ واینکه چطوری باید بهش متصل کنم ...
    ممنون میشم اگه بهم جواب بدین ، کارم خیلی فوریه ...

  38. #20
    عضو جدید
    تاریخ عضویت
    Jun 2011
    نوشته ها
    5
    تشکر
    2
    تشکر شده 2 بار در 2 پست

    پیش فرض

    اه ، آقای نادری شمایین ؟؟؟ بابا من فرزادم !!!
    چطورین ؟ چه خبر ؟

  39. تشکرها از این نوشته :


صفحه 1 از 3 123 آخرینآخرین

مجوز های ارسال و ویرایش

  • شما نمیتوانید موضوع جدیدی ارسال کنید
  • شما امکان ارسال پاسخ را ندارید
  • شما نمیتوانید فایل پیوست کنید.
  • شما نمیتوانید پست های خود را ویرایش کنید
  •