سئوال
سلام
من یک کد برای کنترل یک ترموستات با میکرو دارم که میتونه تو هر 450ثانیه دو تا کلید رو بزنه -مربوط به دکمه set ,و down ترموستات-
من میخوام تو همون زمان بجای یک مرتبه دومرتبه کلیدِdown مورد نظر رو بزنه
کدوم قسمت کد رو باید تغییر بدم؟
کد:/***************************************************** This program was produced by the CodeWizardAVR V2.04.4a Advanced Automatic Program Generator © Copyright 1998-2009 Pavel Haiduc, HP InfoTech s.r.l. http://www.hpinfotech.com Project : Version : Date : 2010/11/23 Author : NeVaDa Company : Warner Brothers Movie World Comments: Chip type : ATmega16 Program type : Application AVR Core Clock frequency: 16.000000 MHz Memory model : Small External RAM size : 0 Data Stack size : 256 *****************************************************/ #include <mega16.h> #include <delay.h> // unsigned char i,flag=0; // Timer 0 output compare interrupt service routine interrupt [TIM0_COMP] void timer0_comp_isr(void) { // Place your code here } // Timer1 output compare A interrupt service routine interrupt [TIM1_COMPA] void timer1_compa_isr(void) { // Place your code here static unsigned int cnt; //cnt=0; PORTA.0=~PORTA.0; if (++cnt == 450) // 450 sec { cnt=0; PORTA.1=~PORTA.1; flag=1; } } // Declare your global variables here void main(void) { // Declare your local variables here // Input/Output Ports initialization // Port A initialization // Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In // State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T PORTA=0xFF; DDRA=0xFF; // Port B initialization // Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In // State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T PORTB=0x00; DDRB=0x00; // Port C initialization // Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In // State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T PORTC=0x00; DDRC=0x81; // Port D initialization // Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In // State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T PORTD=0x00; DDRD=0x00; // Timer/Counter 0 initialization // Clock source: System Clock // Clock value: 250.000 kHz // Mode: CTC top=OCR0 // OC0 output: Disconnected TCCR0=0x0B; TCNT0=0x00; OCR0=0xFA; // Timer/Counter 1 initialization // Clock source: System Clock // Clock value: 15.625 kHz // Mode: CTC top=ICR1 // OC1A output: Discon. // OC1B output: Discon. // Noise Canceler: Off // Input Capture on Falling Edge // Timer1 Overflow Interrupt: Off // Input Capture Interrupt: Off // Compare A Match Interrupt: On // Compare B Match Interrupt: Off TCCR1A=0x00; TCCR1B=0x1D; TCNT1H=0x00; TCNT1L=0x00; ICR1H=0x3d; ICR1L=0x09; OCR1AH=0x00; OCR1AL=0x34; OCR1BH=0x00; OCR1BL=0x00; // Timer/Counter 2 initialization // Clock source: System Clock // Clock value: Timer2 Stopped // Mode: Normal top=FFh // OC2 output: Disconnected ASSR=0x00; TCCR2=0x00; TCNT2=0x00; OCR2=0x00; // External Interrupt(s) initialization // INT0: Off // INT1: Off // INT2: Off MCUCR=0x00; MCUCSR=0x00; // Timer(s)/Counter(s) Interrupt(s) initialization TIMSK=0x12; // Analog Comparator initialization // Analog Comparator: Off // Analog Comparator Input Capture by Timer/Counter 1: Off ACSR=0x80; SFIOR=0x00; // Global enable interrupts #asm("sei") while (1) { // Place your code here if(flag == 1) { flag=0; for (i=0;i<5;i++) { PORTC.0=1; PORTA.7=0; delay_ms(300); PORTC.0=0; PORTA.7=1; delay_ms(300); } delay_ms(2000); //____________________ PORTC.7=1; PORTA.5=0; delay_ms(250); PORTC.7=0; PORTA.5=1; //delay_ms(2000); } }; }
پاسخ با نقل قول
