m44miri
11-02-2015, 15:48
با روش این فیلم آموزشی و این لینک سعی کردم بوت را از SD به NAND منتقل کنم اما همچین پیغامی میده موقع بوت.کسی هست که راهنمایی کنه؟
You can see links before reply
Cubieboard/Installing on NAND - linux-sunxi.org (You can see links before reply)
HELLO! BOOT0 is starting!
boot0 version : 3.0.0
dram size =2048
sum=0x65176209
src_sum=0x65176209
Ready to disable icache.
Jump to secend Boot.
[ 0.155]
U-Boot 2011.09-rc1-00003-ge89ab14-dirty (Jan 03 2014 - 12:57:33) Allwinner Tech
[ 0.164]version: 1.1.0
[ 0.167]pmbus: ready
[ 0.272]PMU: AXP209
[ 0.275]PMU: AXP20x found
[ 0.278]PMU: bat ratio = 100
[ 0.282]after set, dcdc2 =1450mv
[ 0.285]PMU: dcdc2 1450
[ 0.288]PMU: pll1 912 Mhz
boot_clock = 912
dcdc2_vol = 1450
[ 0.296]after set, dcdc2 =1450mv
dcdc3_vol = 1300
ldo2_vol = 3000
ldo3_vol = 2800
ldo4_vol = 2800
power_start = 1
storage_type = -1
usb_recovery = 1
find power_sply to end
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[ 0.332]DRAM: 2 GiB
relocation Offset is: 75b23000
donn't initialize ther user_gpio (main_key:boot_init_gpio)
DRV_DISP_Init: opened
[ 0.546]boot_disp.output_type=4
[ 0.550]boot_disp.output_mode=11
[ 0.553]boot_disp.auto_hpd=1
workmode = 0
[ 1.857]NAND: NAND_UbootInit
NB1 : enter NAND_LogicInit
nand : get id_number_ctl from script, 3
not burn nand partition table!
NB1 : nand_info_init fail
[ 7.436]nand init fail
fail to find part named env
Using default environment
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
mbr not exist
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_nand
key 0
recovery key high 6, low 4
cant find fstbt value
no misc partition is found
to be run cmd=run setargs_nand boot_normal
the part isn't exist
WORK_MODE_BOOT
WORK_MODE_BOOT
[ 7.474]Hit any key to stop autoboot: 0
cant find part named boot
sunxi_flash - sunxi_flash sub-system
Usage:
sunxi_flash read command parmeters :
parmeters 0 : addr to load(hex only)
parmeters 1 : the name of the part to be load
[parmeters 2] : the number of bytes to be load(hex only)
if [parmeters 2] not exist, the number of bytes to be load is the size of the p1
boota: bad boot image magic, maybe not a boot.img?
You can see links before reply
Cubieboard/Installing on NAND - linux-sunxi.org (You can see links before reply)
HELLO! BOOT0 is starting!
boot0 version : 3.0.0
dram size =2048
sum=0x65176209
src_sum=0x65176209
Ready to disable icache.
Jump to secend Boot.
[ 0.155]
U-Boot 2011.09-rc1-00003-ge89ab14-dirty (Jan 03 2014 - 12:57:33) Allwinner Tech
[ 0.164]version: 1.1.0
[ 0.167]pmbus: ready
[ 0.272]PMU: AXP209
[ 0.275]PMU: AXP20x found
[ 0.278]PMU: bat ratio = 100
[ 0.282]after set, dcdc2 =1450mv
[ 0.285]PMU: dcdc2 1450
[ 0.288]PMU: pll1 912 Mhz
boot_clock = 912
dcdc2_vol = 1450
[ 0.296]after set, dcdc2 =1450mv
dcdc3_vol = 1300
ldo2_vol = 3000
ldo3_vol = 2800
ldo4_vol = 2800
power_start = 1
storage_type = -1
usb_recovery = 1
find power_sply to end
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[ 0.332]DRAM: 2 GiB
relocation Offset is: 75b23000
donn't initialize ther user_gpio (main_key:boot_init_gpio)
DRV_DISP_Init: opened
[ 0.546]boot_disp.output_type=4
[ 0.550]boot_disp.output_mode=11
[ 0.553]boot_disp.auto_hpd=1
workmode = 0
[ 1.857]NAND: NAND_UbootInit
NB1 : enter NAND_LogicInit
nand : get id_number_ctl from script, 3
not burn nand partition table!
NB1 : nand_info_init fail
[ 7.436]nand init fail
fail to find part named env
Using default environment
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
mbr not exist
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_nand
key 0
recovery key high 6, low 4
cant find fstbt value
no misc partition is found
to be run cmd=run setargs_nand boot_normal
the part isn't exist
WORK_MODE_BOOT
WORK_MODE_BOOT
[ 7.474]Hit any key to stop autoboot: 0
cant find part named boot
sunxi_flash - sunxi_flash sub-system
Usage:
sunxi_flash read command parmeters :
parmeters 0 : addr to load(hex only)
parmeters 1 : the name of the part to be load
[parmeters 2] : the number of bytes to be load(hex only)
if [parmeters 2] not exist, the number of bytes to be load is the size of the p1
boota: bad boot image magic, maybe not a boot.img?