کد:
;A80 PAD application
;---------------------------------------------------------------------------------------------------------
; 说明： 脚本中的字符串区分大小写，用户可以修改"="后面的数值，但是不要修改前面的字符串
; 描述gpio的形式：Port:端口+组内序号<功能分配><内部电阻状态><驱动能力><输出电平状态>
;---------------------------------------------------------------------------------------------------------
[product]
version = "100"
machine = "optimus"
[platform]
eraseflag = 1
;----------------------------------------------------------------------------------
; system configuration
; ?
;dcdc1_vol ---set dcdc1 voltage,mV,1600-3400,100mV/step
;dcdc2_vol ---set dcdc2 voltage,mV,600-1540,20mV/step
;dcdc3_vol ---set dcdc3 voltage,mV,600-1860,20mV/step
;dcdc4_vol ---set dcdc4 voltage,mV,600-1540,20mV/step
;dcdc5_vol ---set dcdc5 voltage,mV,1000-2550,50mV/step
;aldo2_vol ---set aldo2 voltage,mV,700-3300,100mV/step
;aldo3_vol ---set aldo3 voltage,mV,700-3300,100mV/step
;----------------------------------------------------------------------------------
[target]
boot_clock = 1008
storage_type = -1
[charging_type]
charging_type = 1
;---------------------------------------------------------------------------------
; uboot key detect enable
; 当keyen_flag = 1 时，支持按键检测
; 当keyen_flag = 0 时，不支持
;---------------------------------------------------------------------------------
[key_detect_en]
keyen_flag = 0
;----------------------------------------------------------------------------------
;
; 各路电压输出语法说明：
;
; 电压名称 = 100XXXX : 表示把该路电压设置为XXXX指定的电压值，同时打开输出开关
; 电压名称 = 000XXXX : 表示把该路电压设置为XXXX指定的电压值，同时关闭输出开关，当有需要时由内核驱动打开
; 电压名称 = 0 : 表示关闭该路电压输出开关，不修改原有的值
;
;----------------------------------------------------------------------------------
[power_sply]
dcdc1_vol = 1003000
dcdc2_vol = 900
dcdc3_vol = 1000900
dcdc4_vol = 1000900
dcdc5_vol = 1001500
dc5ldo_vol = 1000900
dldo2_vol = 1003000
eldo3_vol = 1001800
aldo1_vol = 1003000
aldo3_vol = 1003000
[slave_power_sply]
dcdca_vol = 1000900
dcdcb_vol = 0
dcdcc_vol = 0
dcdcd_vol = 1000900
dcdce_vol = 1002100
aldo1_vol = 1003000
bldo1_vol = 1001800
bldo2_vol = 1001800
cldo1_vol = 0
[gpio_bias]
pa_bias = "axp809:gpio1:2500"
pb_bias = "axp809:aldo2:1800"
pc_bias = "axp809:dcdc1:3000"
pd_bias = "axp806:bldo1:1800"
pe_bias = "axp809:eldo2:1800"
pf_bias = "axp809:dcdc1:3000"
pg_bias = "axp809:gpio0:3000"
ph_bias = "axp809:dcdc1:3000"
pl_bias = "axp809:dldo2:3000"
pm_bias = "axp809:eldo3:3000"
[card_boot]
logical_start = 40960
sprite_gpio0 =
next_work = 3
;---------------------------------------------------------------------------------------------------------
; if 1 == standby_mode, then support super standby;
; else, support normal standby.
;---------------------------------------------------------------------------------------------------------
[pm_para]
standby_mode = 1
[card0_boot_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF00<2><1><default><default>
sdc_d0 = port:PF01<2><1><default><default>
sdc_clk = port:PF02<2><1><default><default>
sdc_cmd = port:PF03<2><1><default><default>
sdc_d3 = port:PF04<2><1><default><default>
sdc_d2 = port:PF05<2><1><default><default>
[card2_boot_para]
card_ctrl = 2
card_high_speed = 1
card_line = 4
sdc_cmd = port:PC06<3><1><default><default>
sdc_clk = port:PC07<3><1><default><default>
sdc_d0 = port:PC08<3><1><default><default>
sdc_d1 = port:PC09<3><1><default><default>
sdc_d2 = port:PC10<3><1><default><default>
sdc_d3 = port:PC11<3><1><default><default>
[boot_disp]
output_disp = 1
output_type = 3
output_mode = 10
auto_hpd = 1
[twi_para]
twi_port = 0
twi_scl = port:PH14<2><default><default><default>
twi_sda = port:PH15<2><default><default><default>
[uart_para]
uart_debug_port = 0
uart_debug_tx = port:PH12<2><1><default><default>
uart_debug_rx = port:PH13<2><1><default><default>
[jtag_para]
jtag_enable = 1
jtag_ms = port:PF00<3><default><default><default>
jtag_ck = port:PF05<3><default><default><default>
jtag_do = port:PF03<3><default><default><default>
jtag_di = port:PF01<3><default><default><default>
[clock]
pll4 = 300
pll6 = 600
pll8 = 297
pll9 = 297
pll10 = 2376
;*****************************************************************************
;sdram configuration
;
;dram_para2 = 0x00001200 ;代表启用dram双通道
;
;dram_para2 = 0x00001100 ;代表启用dram单通道
;
;*****************************************************************************
[dram_para]
dram_clk = 672
dram_type = 3
dram_zq = 0x003F3FDD
dram_odt_en = 1
dram_para1 = 0x10f41000
dram_para2 = 0x00001200
dram_mr0 = 0x1A50
dram_mr1 = 0x40
dram_mr2 = 0x10
dram_mr3 = 0
dram_tpr0 = 0x04E214EA
dram_tpr1 = 0x004214AD
dram_tpr2 = 0x10A75030
dram_tpr3 = 0
dram_tpr4 = 0
dram_tpr5 = 0
dram_tpr6 = 0
dram_tpr7 = 0
dram_tpr8 = 0
dram_tpr9 = 0
dram_tpr10 = 0
dram_tpr11 = 0
dram_tpr12 = 168
dram_tpr13 = 0x23
;----------------------------------------------------------------------------------
;os life cycle para configuration
;----------------------------------------------------------------------------------
;------------------------------------------------------------------------------;
; 10/100/100Mbps Ethernet MAC Controller Configure ;
;------------------------------------------------------------------------------;
; 配置选项： ;
; gmac_used --- 1: gmac used, 0: not used ;
;------------------------------------------------------------------------------;
; MII GMII RGMII MII GMII RGMII MII GMII RGMII ;
;PA00~03 * * * PA10 * * PA20 * * * ;
; PA04 * PA11~14 * * * PA21 * * ;
; PA05 * PA15 * PA22 * * ;
; PA06 * PA16 * PA23 * * ;
; PA07 * PA17 * PA24 * * ;
; PA08 * * PA18 * PA25 * * ;
; PA09 * * * PA19 * * * PA26~27 * * * ;
;------------------------------------------------------------------------------;
[gmac0]
gmac_used = 1
gmac_rxd3 = port:PA00<2><default><3><default>
gmac_rxd2 = port:PA01<2><default><3><default>
gmac_rxd1 = port:PA02<2><default><3><default>
gmac_rxd0 = port:PA03<2><default><3><default>
gmac_rxclk = port:PA04<2><default><3><default>
gmac_rxdv = port:PA05<2><default><3><default>
;gmac_rxerr = port:PA06<2><default><3><default>
gmac_txd3 = port:PA07<2><default><3><default>
gmac_txd2 = port:PA08<2><default><3><default>
gmac_txd1 = port:PA09<2><default><3><default>
gmac_txd0 = port:PA10<2><default><3><default>
;gmac_crs = port:PA11<2><default><3><default>
gmac_txclk = port:PA12<2><default><3><default>
gmac_txen = port:PA13<2><default><3><default>
gmac_txerr = port:PA14<2><default><3><default>
gmac_col = port:PA15<2><default><3><default>
gmac_mdc = port:PA16<2><default><3><default>
gmac_mdio = port:PA17<2><default><3><default>
;---------------------------------------------------------------------------------------------------------
; wakeup_src_para:
; sometimes, u would like to add more wakeup src in standby mode, these para will be
; help;
; u need to make sure the standby mode support the wakeup src. Also, some hw
; condition must be guaranteed.
; including:
; cpu_en: power on or off.
; 1: mean power on
; 0: mean power off
; cpu_freq: indicating lowest freq. unit is Mhz;
; dram selfresh_en: selfresh or not.
; 1: enable enter selfresh
; 0: disable enter selfresh
; dram_pll: if not enter selfresh, indicating lowest freq. unit is Mhz;
; wakeup_src: to make the scenario work, the wakeup src is needed.
;---------------------------------------------------------------------------------------------------------
[wakeup_src_para]
cpu_en = 0
cpu_freq = 48
; (cpu:apb:ahb)
pll_ratio = 0x111
dram_selfresh_en = 1
dram_freq = 36
wakeup_src0 =
wakeup_src_wl = port:PL03<4><default><default><0>
wakeup_src_bt = port:PL04<4><default><default><0>
bb_wake_ap = port:PM01<4><default><default><0>
;----------------------------------------------------------------------------------
;i2c configuration
;----------------------------------------------------------------------------------
[twi0]
twi_used = 1
twi_scl = port:PH0<2><default><default><default>
twi_sda = port:PH1<2><default><default><default>
[twi1]
twi_used = 1
twi_scl = port:PH2<2><default><default><default>
twi_sda = port:PH3<2><default><default><default>
[twi2]
twi_used = 0
twi_scl = port:PH4<2><default><default><default>
twi_sda = port:PH5<2><default><default><default>
[twi3]
twi_used = 0
twi_scl = port:PG10<2><default><default><default>
twi_sda = port:PG11<2><default><default><default>
[twi4]
twi_used = 0
twi_scl = port:PB15<4><default><default><default>
twi_sda = port:PB16<4><default><default><default>
;----------------------------------------------------------------------------------
;uart configuration
;uart_type --- 2 (2 wire), 4 (4 wire), 8 (8 wire, full function)
;----------------------------------------------------------------------------------
[uart0]
uart_used = 1
uart_port = 0
uart_type = 2
uart_tx = port:PH12<2><1><default><default>
uart_rx = port:PH13<2><1><default><default>
[uart1]
uart_used = 0
uart_port = 1
uart_type = 8
uart_tx = port:PA0<4><1><default><default>
uart_rx = port:PA1<4><1><default><default>
uart_rts = port:PA2<4><1><default><default>
uart_cts = port:PA3<4><1><default><default>
;uart_dtr = port:PA4<4><1><default><default>
;uart_dsr = port:PA5<4><1><default><default>
;uart_dcd = port:PA6<4><1><default><default>
;uart_ring = port:PA7<4><1><default><default>
[uart2]
uart_used = 1
uart_port = 2
uart_type = 4
uart_tx = port:PG06<2><1><default><default>
uart_rx = port:PG07<2><1><default><default>
uart_rts = port:PG08<2><1><default><default>
uart_cts = port:PG09<2><1><default><default>
[uart3]
uart_used = 0
uart_port = 3
uart_type = 4
uart_tx = port:PB05<3><1><default><default>
uart_rx = port:PB06<3><1><default><default>
uart_rts = port:PB04<3><1><default><default>
uart_cts = port:PB00<3><1><default><default>
[uart4]
uart_used = 0
uart_port = 4
uart_type = 2
uart_tx = port:PG12<2><1><default><default>
uart_rx = port:PG13<2><1><default><default>
uart_rts = port:PG14<2><1><default><default>
uart_cts = port:PG15<2><1><default><default>
[uart5]
uart_used = 0
uart_port = 5
uart_type = 4
uart_tx = port:PE04<4><1><default><default>
uart_rx = port:PE05<4><1><default><default>
uart_rts = port:PE06<4><1><default><default>
uart_cts = port:PE07<4><1><default><default>
;----------------------------------------------------------------------------------
;SPI controller configuration
;----------------------------------------------------------------------------------
[spi0]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PC19<3><1><default><default>
spi_sclk = port:PC02<3><default><default><default>
spi_mosi = port:PC00<3><default><default><default>
spi_miso = port:PC01<3><default><default><default>
[spi1]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 =
spi_sclk =
spi_mosi =
spi_miso =
[spi2]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PE04<3><1><default><default>
spi_sclk = port:PE05<3><default><default><default>
spi_mosi = port:PE06<3><default><default><default>
spi_miso = port:PE07<3><default><default><default>
[spi3]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PH17<2><1><default><default>
spi_cs1 = port:PH18<2><1><default><default>
spi_cs2 = port:PH12<3><1><default><default>
spi_cs3 = port:PH13<3><default><default><default>
spi_sclk = port:PH14<2><default><default><default>
spi_mosi = port:PH15<2><default><default><default>
spi_miso = port:PH16<2><default><default><default>
;----------------------------------------------------------------------------------
;SPI device configuration
;----------------------------------------------------------------------------------
[spi_devices]
spi_dev_num = 1
[spi_board0]
modalias = "m25p32"
max_speed_hz = 33000000
bus_num = 0
chip_select = 0
mode = 0
;----------------------------------------------------------------------------------
;resistance tp configuration
;----------------------------------------------------------------------------------
[rtp_para]
rtp_used = 0
rtp_screen_size = 5
rtp_regidity_level = 5
rtp_press_threshold_enable = 0
rtp_press_threshold = 0x1f40
rtp_sensitive_level = 0xf
rtp_exchange_x_y_flag = 0
;----------------------------------------------------------------------------------
;capacitor tp configuration
;external int function
;wakeup output function
;notice --- tp_int_port & tp_io_port use the same port
;----------------------------------------------------------------------------------
[ctp_para]
ctp_used = 0
ctp_twi_id = 1
ctp_twi_addr = 0x5d
ctp_screen_max_x = 1280
ctp_screen_max_y = 800
ctp_revert_x_flag = 1
ctp_revert_y_flag = 1
ctp_exchange_x_y_flag = 1
ctp_int_port =
ctp_wakeup =
;--------------------------------------------------------------------------------
; CTP automatic detection configuration
;ctp_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[ctp_list_para]
ctp_det_used = 1
ft5x_ts = 1
gt82x = 1
gslX680 = 1
gt9xx_ts = 1
gt811 = 1
zet622x = 1
aw5306_ts = 1
;----------------------------------------------------------------------------------
;touch key configuration
;----------------------------------------------------------------------------------
[tkey_para]
tkey_used = 0
tkey_twi_id =
tkey_twi_addr =
tkey_int =
;----------------------------------------------------------------------------------
;motor configuration
;----------------------------------------------------------------------------------
[motor_para]
motor_used = 0
motor_shake = 0
motor_ldo = axp22_ldoio0
motor_ldo_voltage = 3300
;----------------------------------------------------------------------------------
;thermal configuration
;----------------------------------------------------------------------------------
[ths_para]
ths_used = 1
ths_trend = 0
ths_trip1_count = 5
ths_trip1_0 = 60
ths_trip1_1 = 75
ths_trip1_2 = 85
ths_trip1_3 = 95
ths_trip1_4 = 105
ths_trip1_5 = 0
ths_trip1_6 = 0
ths_trip1_7 = 0
ths_trip1_0_min = 0
ths_trip1_0_max = 1
ths_trip1_1_min = 1
ths_trip1_1_max = 2
ths_trip1_2_min = 2
ths_trip1_2_max = 5
ths_trip1_3_min = 5
ths_trip1_3_max = 9
ths_trip1_4_min = 0
ths_trip1_4_max = 0
ths_trip1_5_min = 0
ths_trip1_5_max = 0
ths_trip1_6_min = 0
ths_trip1_6_max = 0
ths_trip2_count = 1
ths_trip2_0 = 105
;----------------------------------------------------------------------------------
;cooler_table cooler_count <=32
;----------------------------------------------------------------------------------
[cooler_table]
cooler_count = 10
cooler0 = "1200000 4 1800000 4"
cooler1 = "1200000 4 1608000 4"
cooler2 = "1200000 4 1440000 4"
cooler3 = "1200000 4 1200000 4"
cooler4 = "1200000 4 1200000 3"
cooler5 = "1200000 4 1440000 2"
cooler6 = "1200000 4 1200000 2"
cooler7 = "1200000 4 1200000 1"
cooler8 = "1200000 4 4294967295 0"
cooler9 = "600000 4 4294967295 0"
;----------------------------------------------------------------------------------
[nand0_para]
nand_support_2ch = 1
nand0_used = 1
nand0_we = port:PC00<2><default><default><default>
nand0_ale = port:PC01<2><default><default><default>
nand0_cle = port:PC02<2><default><default><default>
nand0_ce1 = port:PC03<2><default><default><default>
nand0_ce0 = port:PC04<2><default><default><default>
nand0_nre = port:PC05<2><default><default><default>
nand0_rb0 = port:PC06<2><default><default><default>
nand0_rb1 = port:PC07<2><default><default><default>
nand0_d0 = port:PC08<2><default><default><default>
nand0_d1 = port:PC09<2><default><default><default>
nand0_d2 = port:PC10<2><default><default><default>
nand0_d3 = port:PC11<2><default><default><default>
nand0_d4 = port:PC12<2><default><default><default>
nand0_d5 = port:PC13<2><default><default><default>
nand0_d6 = port:PC14<2><default><default><default>
nand0_d7 = port:PC15<2><default><default><default>
nand0_ce2 = port:PC17<2><default><default><default>
nand0_ce3 = port:PC18<2><default><default><default>
nand0_ndqs = port:PC16<2><default><default><default>
[nand1_para]
nand1_used = 1
nand1_we = port:PC00<2><default><default><default>
nand1_ale = port:PC01<2><default><default><default>
nand1_cle = port:PC03<2><default><default><default>
nand1_ce1 = port:PC03<2><default><default><default>
nand1_ce0 = port:PC04<2><default><default><default>
nand1_nre = port:PC05<2><default><default><default>
nand1_rb0 = port:PC06<2><default><default><default>
nand1_rb1 = port:PC07<2><default><default><default>
nand1_d0 = port:PC08<2><default><default><default>
nand1_d1 = port:PC09<2><default><default><default>
nand1_d2 = port:PC10<2><default><default><default>
nand1_d3 = port:PC11<2><default><default><default>
nand1_d4 = port:PC12<2><default><default><default>
nand1_d5 = port:PC13<2><default><default><default>
nand1_d6 = port:PC14<2><default><default><default>
nand1_d7 = port:PC15<2><default><default><default>
nand1_ce2 = port:PC17<2><default><default><default>
nand1_ce3 = port:PC18<2><default><default><default>
nand1_ndqs = port:PC16<2><default><default><default>
;----------------------------------------------------------------------------------
;disp init configuration
;
;disp_mode (0:screen0<screen0,fb0>)
;screenx_output_type (0:none; 1:lcd; 3:hdmi;)
;screenx_output_mode (used for hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50)
; (5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60)
;fbx format (0:ARGB 1:ABGR 2:RGBA 3:BGRA)
;fbx_width,fbx_height (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0)
;lcdx_backlight (lcd init backlight,the range:[0,256],default:197
;lcdx_yy (lcd init screen bright/contrast/saturation/hue, value:0~100, default:50/50/57/50)
;----------------------------------------------------------------------------------
[disp_init]
disp_composer_mode = 1
disp_init_enable = 1
disp_mode = 1
screen0_output_type = 1
screen0_output_mode = 1
screen1_output_type = 3
screen1_output_mode = 10
fb0_format = 0
fb0_scaler_mode_enable = 0
fb0_width = 0
fb0_height = 0
fb1_format = 0
fb1_scaler_mode_enable = 0
fb1_width = 0
fb1_height = 0
lcd0_backlight = 197
lcd1_backlight = 197
lcd0_bright = 50
lcd0_contrast = 50
lcd0_saturation = 57
lcd0_hue = 50
lcd1_bright = 50
lcd1_contrast = 50
lcd1_saturation = 57
lcd1_hue = 50
;----------------------------------------------------------------------------------
;lcd0 configuration
;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds; 4:dsi; 5:edp
;lcd_x: lcd horizontal resolution
;lcd_y: lcd vertical resolution
;lcd_width: width of lcd in mm
;lcd_height: height of lcd in mm
;lcd_dclk_freq: in MHZ unit
;lcd_pwm_freq: in HZ unit
;lcd_pwm_pol: lcd backlight PWM polarity
;lcd_pwm_max_limit lcd backlight PWM max limit(<=255)
;lcd_hbp: hsync back porch
;lcd_ht: hsync total cycle
;lcd_vbp: vsync back porch
;lcd_vt: vysnc total cycle
;lcd_hspw: hsync plus width
;lcd_vspw: vysnc plus width
;lcd_lvds_if: 0:single link; 1:dual link
;lcd_lvds_colordepth: 0:8bit; 1:6bit
;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode
;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither
;lcd_gamma_en lcd gamma correction enable
;lcd_bright_curve_en lcd bright curve correction enable
;lcd_cmap_en lcd color map function enable
;deu_mode 0:smoll lcd screen; 1:large lcd screen(larger than 10inch)
;lcdgamma4iep: Smart Backlight parameter, lcd gamma vale * 10;
; decrease it while lcd is not bright enough; increase while lcd is too bright
;smart_color 90:normal lcd screen 65:retina lcd screen(9.7inch)
;vga_used if need vga,lcd_used must be 1,in that case,vga_used is 1 means output to vga
;----------------------------------------------------------------------------------
[lcd0_para]
lcd_used = 1
vga_used = 1
lcd_driver_name = "default_lcd"
lcd_if = 0
lcd_x = 1024
lcd_y = 768
lcd_width = 150
lcd_height = 94
lcd_dclk_freq = 65
lcd_pwm_used = 0
lcd_pwm_ch = 0
lcd_pwm_freq = 50000
lcd_pwm_pol = 0
lcd_hbp = 296
lcd_ht = 1344
lcd_hspw = 136
lcd_vbp = 35
lcd_vt = 806
lcd_vspw = 6
lcd_lvds_if = 0
lcd_lvds_colordepth = 1
lcd_lvds_mode = 0
lcd_frm = 1
lcd_hv_clk_phase = 0
lcd_hv_sync_polarity = 0
lcd_gamma_en = 0
lcd_bright_curve_en = 0
lcd_cmap_en = 0
deu_mode = 0
lcdgamma4iep = 22
smart_color = 90
;lcd_bl_en = port:PA6<1><0><default><1>
lcd_power = port:power2<1><0><default><1>
lcdd0 = port:PD00<2><0><3><default>
lcdd1 = port:PD01<2><0><3><default>
lcdd2 = port:PD02<2><0><3><default>
lcdd3 = port:PD03<2><0><3><default>
lcdd4 = port:PD04<2><0><3><default>
lcdd5 = port:PD05<2><0><3><default>
lcdd6 = port:PD06<2><0><3><default>
lcdd7 = port:PD07<2><0><3><default>
lcdd8 = port:PD08<2><0><3><default>
lcdd9 = port:PD09<2><0><3><default>
lcdd10 = port:PD10<2><0><3><default>
lcdd11 = port:PD11<2><0><3><default>
lcdd12 = port:PD12<2><0><3><default>
lcdd13 = port:PD13<2><0><3><default>
lcdd14 = port:PD14<2><0><3><default>
lcdd15 = port:PD15<2><0><3><default>
lcdd16 = port:PD16<2><0><3><default>
lcdd17 = port:PD17<2><0><3><default>
lcdd18 = port:PD18<2><0><3><default>
lcdd19 = port:PD19<2><0><3><default>
lcdd20 = port:PD20<2><0><3><default>
lcdd21 = port:PD21<2><0><3><default>
lcdd22 = port:PD22<2><0><3><default>
lcdd23 = port:PD23<2><0><3><default>
lcdclk = port:PD24<2><0><default><default>
lcdde = port:PD25<1><0><default><1>
lcdhsync = port:PD26<2><0><3><default>
lcdvsync = port:PD27<2><0><3><default>
;----------------------------------------------------------------------------------
;hdmi configuration
;----------------------------------------------------------------------------------
[hdmi_para]
hdmi_used = 1
;----------------------------------------------------------------------------------
;pwm config
;----------------------------------------------------------------------------------
[pwm0_para]
pwm_used = 0
pwm_positive = port:PH6<2><0><default><default>
[pwm1_para]
pwm_used = 0
pwm_positive = port:PH8<3><0><default><default>
;--------------------------------------------------------------------------------
;vip (video input port) configuration
;vip_used: 0:disable 1:enable
;vip_mode: 0:sample one interface to one buffer 1:sample two interface to one buffer
;vip_dev_qty: The quantity of devices linked to capture bus
;
;vip_define_sensor_list: If you want use sensor detect function, please set vip_define_sensor_list = 1, and
; verify that file /system/etc/hawkview/sensor_list_cfg.ini is properly configured!
;
;vip_dev(x)_pos: sensor position, "rear" or "front", if vip_define_sensor_list = 1,vip_dev(x)_pos must be configured!
;
;vip_dev(x)_isp_used 0:not use isp 1:use isp
;vip_dev(x)_fmt: 0:yuv 1:bayer raw rgb
;vip_dev(x)_stby_mode: 0:not shut down power at standby 1:shut down power at standby
;vip_dev(x)_vflip: flip in vertical direction 0:disable 1:enable
;vip_dev(x)_hflip: flip in horizontal direction 0:disable 1:enable
;vip_dev(x)_iovdd: camera module io power handle string, pmu power supply
;vip_dev(x)_iovdd_vol: camera module io power voltage, pmu power supply
;vip_dev(x)_avdd: camera module analog power handle string, pmu power supply
;vip_dev(x)_avdd_vol: camera module analog power voltage, pmu power supply
;vip_dev(x)_dvdd: camera module core power handle string, pmu power supply
;vip_dev(x)_dvdd_vol: camera module core power voltage, pmu power supply
;vip_dev(x)_afvdd: camera module vcm power handle string, pmu power supply
;vip_dev(x)_afvdd_vol: camera module vcm power voltage, pmu power supply
;x indicates the index of the devices which are linked to the same capture bus
;fill voltage in uV, e.g. iovdd = 2.8V, vip_devx_iovdd_vol = 2800000
;fill handle string as below:
;axp22_eldo3
;axp22_dldo4
;axp22_eldo2
;fill handle string "" when not using any pmu power supply
;--------------------------------------------------------------------------------
[csi0]
vip_used = 0
vip_mode = 0
vip_dev_qty = 1
vip_define_sensor_list = 0
vip_csi_mck = port:PB14<3><default><default><default>
vip_csi_sck = port:PB15<3><default><default><default>
vip_csi_sda = port:PB16<3><default><default><default>
vip_dev0_mname = "ov16825"
vip_dev0_pos = "rear"
vip_dev0_lane = 1
vip_dev0_twi_id = 0
vip_dev0_twi_addr = 0x6c
vip_dev0_isp_used = 1
vip_dev0_fmt = 1
vip_dev0_stby_mode = 0
vip_dev0_vflip = 0
vip_dev0_hflip = 0
vip_dev0_iovdd = "axp22_aldo2"
vip_dev0_iovdd_vol = 2800000
vip_dev0_avdd = "axp15_aldo2"
vip_dev0_avdd_vol = 2800000
vip_dev0_dvdd = "axp22_eldo1"
vip_dev0_dvdd_vol = 1500000
vip_dev0_afvdd = "axp15_cldo2"
vip_dev0_afvdd_vol = 2800000
vip_dev0_power_en =
vip_dev0_reset = port:PB5<1><default><default><default>
vip_dev0_pwdn = port:PB6<1><default><default><default>
vip_dev0_flash_en =
vip_dev0_flash_mode =
vip_dev0_af_pwdn =
vip_dev0_act_used = 1
vip_dev0_act_name = "dw9714_act"
vip_dev0_act_slave = 0x18
vip_dev1_mname = ""
vip_dev1_pos = "front"
vip_dev1_lane = 1
vip_dev1_twi_id = 0
vip_dev1_twi_addr =
vip_dev1_isp_used = 0
vip_dev1_fmt = 1
vip_dev1_stby_mode = 0
vip_dev1_vflip = 0
vip_dev1_hflip = 0
vip_dev1_iovdd = "axp22_eldo3"
vip_dev1_iovdd_vol = 2800000
vip_dev1_avdd = "axp22_dldo4"
vip_dev1_avdd_vol = 2800000
vip_dev1_dvdd = "axp22_eldo2"
vip_dev1_dvdd_vol = 1500000
vip_dev1_afvdd = ""
vip_dev1_afvdd_vol = 2800000
vip_dev1_power_en =
vip_dev1_reset =
vip_dev1_pwdn =
vip_dev1_flash_en =
vip_dev1_flash_mode =
vip_dev1_af_pwdn =
[csi1]
vip_used = 0
;--------------------------------------------------------------------------------
;tv configuration
;
;--------------------------------------------------------------------------------
[tvout_para]
tvout_used =
tvout_channel_num =
tv_en =
[tvin_para]
tvin_used =
tvin_channel_num =
;--------------------------------------------------------------------------------
; SDMMC PINS MAPPING |
; ------------------------------------------------------------------------------|
; Config Guide |
; sdc_used: 1-enable card, 0-disable card |
; sdc_detmode: card detect mode |
; 1-detect card by gpio polling |
; 2-detect card by gpio irq(must use IO with irq function) |
; 3-no detect, always in for boot card |
; 4-manually insert and remove by /proc/driver/sunxi-mmc.x/insert|
; sdc_buswidth: card bus width, 1-1bit, 4-4bit, 8-8bit |
; sdc_use_wp: 1-with write protect IO, 0-no write protect IO |
; sdc_isio: for sdio card |
; sdc_regulator: power control.if card supports UHS-I/DDR and HS200 timing for|
; SD3.0 or eMMC4.5, regulator must be configured. the value is |
; the ldo name of AXP221, eg: sdc_regulator = "axp22_eldo2" |
; other: GPIO Mapping configuration |
; ------------------------------------------------------------------------------|
; Note: |
; 1 if detmode=2, sdc_det's config=6 |
; else if detmode=1, sdc_det's config=0 |
; else sdc_det IO is not necessary |
; 2 if the customer wants to support UHS-I and HS200 features, he must provide|
; an independent power supply for the card. This is only used in platforms |
; that supports SD3.0 cards and eMMC4.4+ flashes |
;--------------------------------------------------------------------------------
[mmc0_para]
sdc_used = 1
sdc_detmode = 2
sdc_buswidth = 4
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_d1 = port:PF00<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_det = port:PH18<6><1><2><default>
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"
[mmc1_para]
sdc_used = 1
sdc_detmode = 4
sdc_buswidth = 4
sdc_clk = port:PG00<2><1><2><default>
sdc_cmd = port:PG01<2><1><2><default>
sdc_d0 = port:PG02<2><1><2><default>
sdc_d1 = port:PG03<2><1><2><default>
sdc_d2 = port:PG04<2><1><2><default>
sdc_d3 = port:PG05<2><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 1
sdc_regulator = "none"
[mmc2_para]
sdc_used = 0
sdc_detmode = 3
sdc_buswidth = 8
sdc_clk = port:PC07<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>
sdc_d4 = port:PC12<3><1><2><default>
sdc_d5 = port:PC13<3><1><2><default>
sdc_d6 = port:PC14<3><1><2><default>
sdc_d7 = port:PC15<3><1><2><default>
emmc_rst = port:PC16<3><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"
[mmc3_para]
sdc_used = 0
sdc_detmode = 4
sdc_buswidth = 8
sdc_clk = port:PC07<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>
sdc_d4 = port:PC12<3><1><2><default>
sdc_d5 = port:PC13<3><1><2><default>
sdc_d6 = port:PC14<3><1><2><default>
sdc_d7 = port:PC15<3><1><2><default>
emmc_rst = port:PC16<3><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"
; ------------------------------------------------------------------------------|
; sim card configuration
;--------------------------------------------------------------------------------
[smc_para]
smc_used =
smc_rst =
smc_vppen =
smc_vppp =
smc_det =
smc_vccen =
smc_sck =
smc_sda =
;--------------------------------
;[usbc0]：控制器0的配置。
;usb_used：USB使能标志。置1，表示系统中USB模块可用,置0,则表示系统USB禁用。
;usb_port_type：USB端口的使用情况。 0：device only;1：host only;2：OTG
;usb_detect_type：USB端口的检查方式。0：不做检测;1：vbus/id检查;2：id/dpdm检查
;usb_id_gpio：USB ID pin脚配置。具体请参考gpio配置说明。
;usb_det_vbus_gpio：USB DET_VBUS pin脚配置。具体请参考gpio配置说明。
;usb_drv_vbus_gpio：USB DRY_VBUS pin脚配置。具体请参考gpio配置说明。
;usb_det_vbus_gpio: "axp_ctrl",表示axp 提供
;usb_restrict_gpio usb限流控制pin
;usb_restric_flag: usb限流标置
;--------------------------------
;--------------------------------
;--- USB0控制标志
;--------------------------------
[usbc0]
usb_used = 1
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PH16<0><1><default><default>
usb_det_vbus_gpio = "axp_ctrl"
usb_drv_vbus_gpio = port:power4<1><0><default><1>
usb_restrict_gpio =
usb_host_init_state = 1
usb_restric_flag =
usb_restric_voltage = 3550000
usb_restric_capacity= 5
;--------------------------------
;--- USB1控制标志
;--------------------------------
[usbc1]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_drv_vbus_gpio = port:PH14<1><0><default><0>
usb_restrict_gpio =
usb_host_init_state = 1
usb_restric_flag = 0
;--------------------------------
;--- USB2控制标志
;--------------------------------
[usbc2]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_drv_vbus_gpio = port:PH15<1><0><default><0>
usb_restrict_gpio =
usb_host_init_state = 1
usb_restric_flag = 0
;--------------------------------
;--- USB3控制标志
;--------------------------------
[usbc3]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_drv_vbus_gpio =
usb_restrict_gpio =
usb_host_init_state = 1
usb_restric_flag = 0
;--------------------------------
;--- USB Device
;--------------------------------
[usb_feature]
vendor_id = 0x18D1
mass_storage_id = 0x0001
adb_id = 0x0002
manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"
[msc_feature]
vendor_name = "USB 2.0"
product_name = "USB Flash Driver"
release = 100
luns = 3
[serial_feature]
serial_unique = 0
;--------------------------------------------------------------------------------
; G sensor configuration
; gs_twi_id --- TWI ID for controlling Gsensor (0: TWI0, 1: TWI1, 2: TWI2)
;--------------------------------------------------------------------------------
[gsensor_para]
gsensor_used = 0
gsensor_twi_id = 1
gsensor_twi_addr = 0x18
gsensor_int1 = port:PH17<6><1><default><default>
gsensor_int2 =
;--------------------------------------------------------------------------------
; G sensor automatic detection configuration
;gsensor_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[gsensor_list_para]
gsensor_det_used = 1
bma250 = 1
mma8452 = 1
mma7660 = 1
mma865x = 1
afa750 = 1
lis3de_acc = 1
lis3dh_acc = 1
kxtik = 1
dmard10 = 0
dmard06 = 1
mxc622x = 1
fxos8700 = 1
lsm303d = 1
;--------------------------------------------------------------------------------
; gps gpio configuration
; gps_spi_id --- the index of SPI controller. 0: SPI0, 1: SPI1, 2: SPI2, 15: no SPI used
; gps_spi_cs_num --- the chip select number of SPI controller. 0: SPI CS0, 1: SPI CS1
; gps_lradc --- the lradc number for GPS used. 0 and 1 is valid, set 2 if not use lradc
;--------------------------------------------------------------------------------
[gps_para]
;--------------------------------------------------------------------------------
;wifi configuration
;wifi_sdc_id --- 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3
;wifi_usbc_id --- 0- USB0, 1- USB1, 2- USB2, 3- USB3
;wifi_mod_sel --- 0- none, 1- rtl8188eu, 2- rtl8723bs(wifi+bt),
; 3 - ap6181, 4- ap6210(wifi+bt), 5 - ap6330(wifi+bt)
;--------------------------------------------------------------------------------
[wifi_para]
wifi_used = 1
wifi_sdc_id = 1
wifi_usbc_id = 1
wifi_usbc_type = 1
wifi_mod_sel = 5
wifi_power = "axp22_dldo1"
wifi_power_ext1 = "axp15_cldo3"
wifi_power_ext2 = "axp22_ldoio0"
sdio_power = ""
; 1 - rtl8188eu usb wifi gpio conifg
;rtl8188eu_power = port:PH27<1><0><default><0>
; 2 - rtl8723bs sdio wifi + bt gpio config
rtl8723bs_chip_en = port:PL09<1><default><default><0>
rtl8723bs_wl_regon = port:PL02<1><default><default><0>
rtl8723bs_wl_host_wake = port:PL03<4><default><default><0>
rtl8723bs_bt_regon = port:PL05<1><default><default><0>
rtl8723bs_bt_wake = port:PL08<1><default><default><0>
rtl8723bs_bt_host_wake = port:PL04<4><default><default><0>
rtl8723bs_lpo_use_apclk = 0
; 3 - ap6181 sdio wifi gpio config
; 4 - ap6210 sdio wifi + bt gpio config
; 5 - ap6330 sdio wifi + bt gpio config
ap6xxx_wl_regon = port:PL02<1><default><default><0>
ap6xxx_wl_host_wake = port:PL03<0><default><default><0>
ap6xxx_bt_regon = port:PL05<1><default><default><0>
ap6xxx_bt_wake = port:PL08<1><default><default><0>
ap6xxx_bt_host_wake = port:PL04<0><default><default><0>
ap6xxx_lpo_use_apclk = 2
;--------------------------------------------------------------------------------
;3G configuration
;--------------------------------------------------------------------------------
[3g_para]
3g_used = 0
3g_usbc_num = 3
3g_uart_num = 4
bb_name = "mu509"
bb_vbat =
bb_on = port:PM02<1><default><default><0>
bb_pwr_on = port:PM03<1><default><default><0>
bb_wake = port:PM04<1><default><default><0>
bb_rf_dis = port:PM15<1><default><default><0>
bb_rst = port:PM00<1><default><default><0>
bb_dldo = "axp22_sw0"
bb_dldo_min_uV = 5000000
bb_dldo_max_uV = 5000000
;--------------------------------------------------------------------------------
;gyroscope
;--------------------------------------------------------------------------------
[gy_para]
gy_used = 1
gy_twi_id = 1
gy_twi_addr = 0x6a
gy_int1 = port:PH15<6><1><default><default>
gy_int2 =
;--------------------------------------------------------------------------------
; Gyro automatic detection configuration
;gy_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[gy_list_para]
gy_det_used = 0
l3gd20_gyr = 1
;--------------------------------------------------------------------------------
;light sensor
;--------------------------------------------------------------------------------
[ls_para]
ls_used = 0
ls_twi_id = 1
ls_twi_addr = 0x23
ls_int = port:PH17<6><1><default><default>
;--------------------------------------------------------------------------------
; lsensor automatic detection configuration
;ls_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[ls_list_para]
ls_det_used = 0
ltr_501als = 1
;--------------------------------------------------------------------------------
;compass
;--------------------------------------------------------------------------------
[compass_para]
compass_used = 0
compass_twi_id = 1
compass_twi_addr = 0x0d
compass_int =
;--------------------------------------------------------------------------------
;led
;--------------------------------------------------------------------------------
[leds_para]
leds_used = 1
leds_num = 2
leds_pin_1 = port:PH06<1><default><default><0>
leds_name_1 = "blue:ph21:led1"
leds_default_1 = 0
leds_trigger_1 = "heartbeat"
leds_pin_2 = port:PH17<1><default><default><0>
leds_name_2 = "orange:ph20:led2"
leds_default_2 = 0
leds_trigger_2 = "cpu0"
;leds_pin_3 = port:PH11<1><default><default><0>
;leds_name_3 = "white:ph11:led3"
;leds_default_3 = 0
;leds_trigger_3 = "cpu1"
;leds_pin_4 = port:PH07<1><default><default><0>
;leds_name_4 = "green:ph07:led4"
;leds_default_4 = 1
;leds_trigger_4 = "mmc0"
;--------------------------------------------------------------------------------
;blue tooth
;bt_used ---- blue tooth used (0- no used, 1- used)
;bt_uard_id ---- uart index
;--------------------------------------------------------------------------------
[bt_para]
bt_used = 1
bt_uart_id = 2
bt_wakeup =
bt_gpio =
bt_rst =
;--------------------------------------------------------------------------------
;daudio_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use
; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use
; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use
; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use
;daudio_select:0 is pcm.1 is i2s
;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use
; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format).
; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format)
; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use
; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge)
;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use
; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM)
; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use
; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM)
;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs
;sample_resolution :16bits/20bits/24bits
;word_select_size :16bits/20bits/24bits/32bits
;pcm_sync_period :16/32/64/128/256
;msb_lsb_first :0: msb first; 1: lsb first
;sign_extend :0: zero pending; 1: sign extend
;slot_index :slot index: 0: the 1st slot - 3: the 4th slot
;slot_width :8 bit width / 16 bit width
;frame_width :0: long frame = 2 clock width; 1: short frame
;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;--------------------------------------------------------------------------------
[s_i2s1]
daudio_used = 1
daudio_master = 4
daudio_select = 1
audio_format = 1
signal_inversion = 1
mclk_fs = 512
sample_resolution = 16
slot_width_select = 16
;pcm_sync_period = 256
pcm_lrck_period = 32
pcm_lrckr_period = 1
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
frame_width = 0
tx_data_mode = 0
rx_data_mode = 0
s_i2s1_lrckr = port:PM04<3><1><default><default>
s_i2s1_dout1 = port:PM05<3><1><default><default>
s_i2s1_dout2 = port:PM06<3><1><default><default>
s_i2s1_dout3 = port:PM07<3><1><default><default>
s_i2s1_mclk = port:PM10<3><1><default><default>
s_i2s1_bclk = port:PM11<3><1><default><default>
s_i2s1_lrclk = port:PM12<3><1><default><default>
s_i2s1_din = port:PM13<3><1><default><default>
s_i2s1_dout0 = port:PM14<3><1><default><default>
[audio0]
audio_int_ctrl = port:PL9<6><default><default><0>
audio_pa_ctrl = port:PA16<1><default><default><0>
audio_hp_det = port:PM00<0><default><default><0>
aif3_voltage = "axp15_cldo3"
Digital_bb_cap_keytone_used = 0
;speaker_val = 0x1b
headset_val = 0x3b
single_speaker_val = 0x19
double_speaker_val = 0x1b
speaker_double_used = 1
[spdif0]
spdif_used = 0
spdif_dout = port:PH18<3><1><default><default>
spdif_din = port:PH17<3><1><default><default>
spdif_voltage = "axp22_dcdc1"
;----------------------------------------------------------------------------------
;ir rx --- infra remote configuration
;----------------------------------------------------------------------------------
[s_cir0]
ir_used = 1
ir_rx = port:PL06<3><1><default><default>
ir_power_key_code = 0x0
ir_addr_code = 0x0
;----------------------------------------------------------------------------------
;ir tx--- infra remote configuration
;----------------------------------------------------------------------------------
[cir]
ir_used = 1
ir_tx = port:PH07<2><default><default><default>
;-------------------------------------------------------------------------------------
;pmu_used ---0:not used,1:used
;pmu_twi_addr ---slave address
;pmu_twi_id ---i2c bus number (0 TWI0, 1 TWI2, 2 TWI3)
;pmu_irq_id ---irq number (0 irq0,1 irq1,……)
;pmu_battery_rdc ---battery initial resistance
;pmu_battery_cap ---battery capability,mAh
;pmu_batdeten ---battery detect en;0:disable 1:enable
;pmu_runtime_chgcur ---set initial charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_earlysuspend_chgcur ---set earlysuspend charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_suspend_chgcur ---set suspend charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_shutdown_chgcur ---set shutdown charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_init_chgvol ---set initial charing target voltage,mV,4100/4220/4200/4240
;pmu_init_chgend_rate ---set initial charing end current rate,10/15
;pmu_init_chg_enabled ---set initial charing enabled,0:disable,1:enable
;pmu_init_adc_freq ---set initial adc frequency,Hz,100/200/400/800
;pmu_init_adcts_freq ---set initial adc TS,Hz,100/200/400/800
;pmu_init_chg_pretime ---set initial pre-charging time,min,40/50/60/70
;pmu_init_chg_csttime ---set initial constance-charging time,min,360/480/600/720
;pmu_batt_cap_correct ---correct the battery capacity or not when one charge cycle 0:not correct 1:correct
;pmu_bat_regu_en ---bat regulator is enable or not when charge done 0:disable 1:enable
;pmu_bat_para1 ---battery indication at 3.13V
;pmu_bat_para2 ---battery indication at 3.27V
;pmu_bat_para3 ---battery indication at 3.34V
;pmu_bat_para4 ---battery indication at 3.41V
;pmu_bat_para5 ---battery indication at 3.48V
;pmu_bat_para6 ---battery indication at 3.52V
;pmu_bat_para7 ---battery indication at 3.55V
;pmu_bat_para8 ---battery indication at 3.57V
;pmu_bat_para9 ---battery indication at 3.59V
;pmu_bat_para10 ---battery indication at 3.61V
;pmu_bat_para11 ---battery indication at 3.63V
;pmu_bat_para12 ---battery indication at 3.64V
;pmu_bat_para13 ---battery indication at 3.66V
;pmu_bat_para14 ---battery indication at 3.7V
;pmu_bat_para15 ---battery indication at 3.73V
;pmu_bat_para16 ---battery indication at 3.77V
;pmu_bat_para17 ---battery indication at 3.78V
;pmu_bat_para18 ---battery indication at 3.8V
;pmu_bat_para19 ---battery indication at 3.82V
;pmu_bat_para20 ---battery indication at 3.84V
;pmu_bat_para21 ---battery indication at 3.85V
;pmu_bat_para22 ---battery indication at 3.87V
;pmu_bat_para23 ---battery indication at 3.91V
;pmu_bat_para24 ---battery indication at 3.94V
;pmu_bat_para25 ---battery indication at 3.98V
;pmu_bat_para26 ---battery indication at 4.01V
;pmu_bat_para27 ---battery indication at 4.05V
;pmu_bat_para28 ---battery indication at 4.08V
;pmu_bat_para29 ---battery indication at 4.1V
;pmu_bat_para30 ---battery indication at 4.12V
;pmu_bat_para31 ---battery indication at 4.14V
;pmu_bat_para32 ---battery indication at 4.15V
;pmu_usbvol_limit ---set usb-ac limited voltage enable,1:enable，0：disable
;pmu_usbcur_limit ---set usb-ac limited current enable,1:enable，0：disable
;pmu_usbvol ---set usb-ac limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite
;pmu_usbcur ---set usb-ac limited current level,mA,500/900, 0 - not limite
;pmu_usbvol_pc ---set usb-pc limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite
;pmu_usbcur_pc ---set usb-pc limited current level,mA,500/900, 0 - not limite
;pmu_pwroff_vol ---set protect voltage when system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pwron_vol ---set protect voltage after system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pekoff_time ---set pek off time,ms, 4000/6000/8000/10000
;pmu_pekoff_func ---set pek off func, 0:shutdown,1:restart
;pmu_pekoff_en ---set pek offlevel powerdown or not, 0:not powerdown,1:powerdown
;pmu_pekoff_delay_time ---set pek off delay time s, 0/10/20/30/40/50/60/70
;pmu_peklong_time ---set pek pek long irq time,ms,1000/1500/2000/2500
;pmu_pekon_time ---set pek on time,ms,128/1000/2000/3000
;pmu_pwrok_time ---set pmu pwrok delay time,ms,8/16/32/64
;pmu_pwrok_shutdown_en ---set pwrok 6s shutdown enable
;pmu_battery_warning_level1 ---low power warning high level,5%-20%,1%/step
;pmu_battery_warning_level2 ---low power warning low level,0%-15%,1%/step
;pmu_restvol_time ---battery indicaton reflash time,30/60/120/
;pmu_ocv_cou_adjust_time ---ocv battery indication reflash time,60/120/30
;pmu_chgled_func ---CHGKED pin control，0:controlled by pmu,1:controlled by Charger
;pmu_chgled_type ---CHGLED Type select when pmu_chgled_func=0,0:Type A，1：Type B
;pmu_vbusen_func ---N_VBUSEN function select,0:as an output,1:as an input
;pmu_reset ---when power key press longer than 16's,PMU reset or not.0:not reset 1:reset
;pmu_IRQ_wakeup ---press IRQ wakeup or not when sleep or power down.0:not wakeup 1:wakeup
;pmu_hot_shutdowm ---when PMU over temperature protect or not;0:disable 1:enable
;pmu_inshort ---ACIN and VBUS inshort or not by software;0:auto detect 1:inshort
;pmu_charge_ltf ---
;pmu_charge_htf ---
;pmu_discharge_ltf ---
;pmu_discharge_htf ---
;pmu_temp_para1 --- temp -25 voltage
;pmu_temp_para2 --- temp -15 voltage
;pmu_temp_para3 --- temp -10 voltage
;pmu_temp_para4 --- temp -5 voltage
;pmu_temp_para5 --- temp 0 voltage
;pmu_temp_para6 --- temp 5 voltage
;pmu_temp_para7 --- temp 10 voltage
;pmu_temp_para8 --- temp 20 voltage
;pmu_temp_para9 --- temp 30 voltage
;pmu_temp_para10 --- temp 40 voltage
;pmu_temp_para11 --- temp 45 voltage
;pmu_temp_para12 --- temp 50 voltage
;pmu_temp_para13 --- temp 55 voltage
;pmu_temp_para14 --- temp 60 voltage
;pmu_temp_para15 --- temp 70 voltage
;pmu_temp_para16 --- temp 80 voltage
;--------------------------------------------------------------------------------------------------------
;--------------------------------------------------------------------------------------------------------
;pmu1 is axp22
;--------------------------------------------------------------------------------------------------------
[pmu1_para]
pmu_used = 1
pmu_twi_addr = 0x34
pmu_twi_id = 0
pmu_irq_id = 0
pmu_battery_rdc = 100
pmu_battery_cap = 0
pmu_batdeten = 1
pmu_runtime_chgcur = 900
pmu_earlysuspend_chgcur = 900
pmu_suspend_chgcur = 1500
pmu_shutdown_chgcur = 1500
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 800
pmu_init_adcts_freq = 800
pmu_init_chg_pretime = 70
pmu_init_chg_csttime = 720
pmu_batt_cap_correct = 1
pmu_bat_regu_en = 0
pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 0
pmu_bat_para6 = 0
pmu_bat_para7 = 0
pmu_bat_para8 = 0
pmu_bat_para9 = 5
pmu_bat_para10 = 8
pmu_bat_para11 = 9
pmu_bat_para12 = 10
pmu_bat_para13 = 13
pmu_bat_para14 = 16
pmu_bat_para15 = 20
pmu_bat_para16 = 33
pmu_bat_para17 = 41
pmu_bat_para18 = 46
pmu_bat_para19 = 50
pmu_bat_para20 = 53
pmu_bat_para21 = 57
pmu_bat_para22 = 61
pmu_bat_para23 = 67
pmu_bat_para24 = 73
pmu_bat_para25 = 78
pmu_bat_para26 = 84
pmu_bat_para27 = 88
pmu_bat_para28 = 92
pmu_bat_para29 = 93
pmu_bat_para30 = 94
pmu_bat_para31 = 95
pmu_bat_para32 = 100
pmu_usbvol_limit = 0
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 0
pmu_usbvol_pc = 4400
pmu_usbcur_pc = 500
pmu_pwroff_vol = 3300
pmu_pwron_vol = 2600
pmu_pekoff_time = 6000
pmu_pekoff_func = 0
pmu_pekoff_en = 1
pmu_pekoff_delay_time = 0
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_pwrok_shutdown_en = 0
pmu_battery_warning_level1 = 15
pmu_battery_warning_level2 = 0
pmu_restvol_adjust_time = 60
pmu_ocv_cou_adjust_time = 60
pmu_chgled_func = 0
pmu_chgled_type = 0
pmu_vbusen_func = 1
pmu_reset = 0
pmu_IRQ_wakeup = 0
pmu_hot_shutdowm = 1
pmu_inshort = 0
power_start = 1
pmu_temp_enable = 0
pmu_charge_ltf = 2261
pmu_charge_htf = 388
pmu_discharge_ltf = 3200
pmu_discharge_htf = 237
pmu_temp_para1 = 7466
pmu_temp_para2 = 4480
pmu_temp_para3 = 3518
pmu_temp_para4 = 2786
pmu_temp_para5 = 2223
pmu_temp_para6 = 1788
pmu_temp_para7 = 1448
pmu_temp_para8 = 969
pmu_temp_para9 = 664
pmu_temp_para10 = 466
pmu_temp_para11 = 393
pmu_temp_para12 = 333
pmu_temp_para13 = 283
pmu_temp_para14 = 242
pmu_temp_para15 = 179
pmu_temp_para16 = 134
;--------------------------------------------------------------------------------------------------------
;pmu2 is axp15
;pmu_used ---0:not used,1:used
;pmu_twi_addr ---slave address
;pmu_twi_id ---i2c bus number (0 TWI0, 1 TWI2, 2 TWI3)
;pmu_irq_id ---irq number (0 irq0,1 irq1)
;pmu_hot_shutdowm ---when PMU over temperature protect or not;0:disable 1:enable
;--------------------------------------------------------------------------------------------------------
[pmu2_para]
pmu_used = 1
pmu_twi_addr = 0x34
pmu_twi_id = 1
pmu_irq_id = 0
pmu_hot_shutdowm = 1
;----------------------------------------------------------------------------------
; dvfs voltage-frequency table configuration
;
; there are two clusters, cluster0 and cluster1, they have diffrent configuration
; on frequency and voltage.
;
; max_freq: cpu maximum frequency, based on Hz
; min_freq: cpu minimum frequency, based on Hz
;
; LV_count: count of LV_freq/LV_volt, must be < 16
;
; L_LV1: core vdd is 1.02v if cpu frequency is (1128Mhz, 1200Mhz]
; L_LV2: core vdd is 0.96v if cpu frequency is (1008Mhz, 1128Mhz]
; L_LV3: core vdd is 0.90v if cpu frequency is ( 864Mhz, 1008Mhz]
; L_LV4: core vdd is 0.84v if cpu frequency is ( 0Mhz, 864Mhz]
; L_LV5: core vdd is 0.84v if cpu frequency is ( 0Mhz, 864Mhz]
; L_LV6: core vdd is 0.84v if cpu frequency is ( 0Mhz, 864Mhz]
; L_LV7: core vdd is 0.84v if cpu frequency is ( 0Mhz, 864Mhz]
; L_LV8: core vdd is 0.84v if cpu frequency is ( 0Mhz, 864Mhz]
;
; B_LV1: core vdd is 1.08v if cpu frequency is (1608Mhz, 1800Mhz]
; B_LV2: core vdd is 1.00v if cpu frequency is (1536Mhz, 1608Mhz]
; B_LV3: core vdd is 0.96v if cpu frequency is (1440Mhz, 1536Mhz]
; B_LV4: core vdd is 0.90v if cpu frequency is (1296Mhz, 1440Mhz]
; B_LV5: core vdd is 0.84v if cpu frequency is ( 0Mhz, 1296Mhz]
; B_LV6: core vdd is 0.84v if cpu frequency is ( 0Mhz, 1296Mhz]
; B_LV7: core vdd is 0.84v if cpu frequency is ( 0Mhz, 1296Mhz]
; B_LV8: core vdd is 0.84v if cpu frequency is ( 0Mhz, 1296Mhz]
;
;----------------------------------------------------------------------------------
[dvfs_table]
vf_table_count = 2
[vf_table0]
;little
L_max_freq = 1200000000
L_min_freq = 912000000
L_LV_count = 4
L_LV1_freq = 1200000000
L_LV1_volt = 1020
L_LV2_freq = 1104000000
L_LV2_volt = 960
L_LV3_freq = 1008000000
L_LV3_volt = 900
L_LV4_freq = 0
L_LV4_volt = 840
;big
B_max_freq = 1800000000
B_min_freq = 1200000000
B_LV_count = 5
B_LV1_freq = 1800000000
B_LV1_volt = 1100
B_LV2_freq = 1608000000
B_LV2_volt = 1020
B_LV3_freq = 1416000000
B_LV3_volt = 960
B_LV4_freq = 1200000000
B_LV4_volt = 900
B_LV5_freq = 0
B_LV5_volt = 840
[vf_table1]
;little
L_max_freq = 1200000000
L_min_freq = 912000000
L_LV_count = 4
L_LV1_freq = 1200000000
L_LV1_volt = 1020
L_LV2_freq = 1104000000
L_LV2_volt = 960
L_LV3_freq = 1008000000
L_LV3_volt = 900
L_LV4_freq = 0
L_LV4_volt = 840
;big
B_max_freq = 1800000000
B_min_freq = 1200000000
B_LV_count = 5
B_LV1_freq = 1800000000
B_LV1_volt = 1100
B_LV2_freq = 1608000000
B_LV2_volt = 1020
B_LV3_freq = 1416000000
B_LV3_volt = 960
B_LV4_freq = 1200000000
B_LV4_volt = 900
B_LV5_freq = 0
B_LV5_volt = 840
;----------------------------------------------------------------------------------
;virtual device
;virtual device for pinctrl testing
;device have pin PA1 PA2
;----------------------------------------------------------------------------------
[Vdevice]
Vdevice_used = 1
Vdevice_0 =
Vdevice_1 =
;----------------------------------------------------------------------------------
;s_uart0 config parameters
;s_uart_used --s_uart0 whether used for arisc debugging
;
;----------------------------------------------------------------------------------
[s_uart0]
s_uart_used = 1
s_uart_tx = port:PL00<3><default><default><default>
s_uart_rx = port:PL01<3><default><default><default>
;----------------------------------------------------------------------------------
;s_rsb0 config parameters
;s_rsb_used --s_rsb0 whether used for arisc
;
;----------------------------------------------------------------------------------
[s_rsb0]
s_rsb_used = 1
s_rsb_sck = port:PN00<3><1><2><default>
s_rsb_sda = port:PN01<3><1><2><default>
;----------------------------------------------------------------------------------
;s_jtag0 config parameters
;s_jtag0_used --s_jtag0 whether used for arisc
;
;----------------------------------------------------------------------------------
[s_jtag0]
s_jtag_used = 1
s_jtag_tms = port:PL02<3><1><2><default>
s_jtag_tck = port:PL03<3><1><2><default>
s_jtag_tdo = port:PL04<3><1><2><default>
s_jtag_tdi = port:PL05<3><1><2><default>
;----------------------------------------------------------------------------------
;s_powchk cpus power check
;s_powchk_used --power check whether used for arisc in super standby
; bit31:enable power updat, bit1:wakeup when power state exception
; bit0:wakeup when power consumption exception
;s_power_reg the expected regs stand for power on/off state
;s_system_power the limit maxmum power consumption when super standby (unit: mw)
;
;----------------------------------------------------------------------------------
[s_powchk]
s_powchk_used = 0x80000000
s_power_reg = 0x02309621
s_system_power = 50
;----------------------------------------------------------------------------------
; dram dvfs voltage-frequency table configuration
;
; LV_count: count of LV_freq/LV_volt
;
; LV1: core vdd is 0.90v if dram frequency is (360Mhz, 672Mhz]
; LV2: core vdd is 0.84v if dram frequency is ( 0Mhz, 168Mhz]
; LV3: core vdd is 0.84v if dram frequency is ( 0Mhz, 168Mhz]
;
;----------------------------------------------------------------------------------
[dram_dvfs_table]
LV_count = 3
LV1_freq = 672000000
LV1_volt = 900
LV2_freq = 168000000
LV2_volt = 840
LV3_freq = 0
LV3_volt = 840
;----------------------------------------------------------------------------------
; dram scene frequency table configuration
;
; LV_count: count of LV_scene/LV_freq
;
; LV0: dram frequency default is 672MHz in normal
; LV1: dram frequency default is 480MHz in home, supported for 480MHz/672MHz
; LV2: dram frequency default is 240MHz in video play, supported for 240MHz/336MHz/480MHz/672MHz
; LV3: dram frequency default is 168MHz in bgmusic play
; LV4: dram frequency default is 480MHz in 4K video play, supported for 480MHz/672MHz
;
;----------------------------------------------------------------------------------
[dram_scene_table]
LV_count = 5
LV0_scene = 0
LV0_freq = 672000000
LV1_scene = 1
LV1_freq = 480000000
LV2_scene = 2
LV2_freq = 240000000
LV3_scene = 3
LV3_freq = 168000000
LV4_scene = 4
LV4_freq = 480000000
مشکل hdmi کوبی بورد 4
پاسخ با نقل قول
نوشته اصلی توسط hmm
